manualshive.com logo in svg

Hawkeye Mfg RG1300, Installation Manual, Page: 4 / 60

Share
Download
Hawkeye Mfg RG1300 Installation Manual Download Page 4

Table of Contents

ii

Hawkeye® Installation Manual for RoGator C-Series RG900, RG1100, RG1300

System Diagrams .......................................................................................................................................................

39

Appendix A 

Sidekick Pro™ ICD Installation..........................................................................  

43

Sidekick Pro ICD Connections to PCB ...............................................................................................................

43

Sidekick Pro ICD Cable to Pump Connections ...............................................................................................

44

Sidekick Pro ICD Power Supply ............................................................................................................................

45

Chapter B 

Cable and Connector Maintenance.................................................................  

47

Power and ECU Harness Maintenance ..............................................................................................................

47

Hawkeye Boom Harness Connector Maintenance .......................................................................................

47

Appendix C 

Special Configuration for ProStop-E Combination Kits .............................  

51

Section Widths ...........................................................................................................................................................

51

Switch Mapping .........................................................................................................................................................

52

Summary of Contents for RG1300





























































Reviews:

No comments