background image

 

016-0171-686 Rev. A 8/18 E31924 

W

e S

ol

ve Grea

t C

ha

lleng

es.

 

DISCLAIMER 

While every effort has been made to ensure the accuracy of this document, Raven Industries assumes no 

responsibility for omissions and errors. Nor is any liability assumed for damages resulting from the use of 

information contained herein.  

Raven Industries shall not be responsible or liable for incidental or consequential damages or a loss of anticipated 

benefits or profits, work stoppage or loss, or impairment of data arising out of the use, or inability to use, this 

system or any of its components. Raven Industries shall not be held responsible for any modifications or repairs 

made outside our facilities, nor damages resulting from inadequate maintenance of this system.  

As with all wireless and satellite signals, several factors may affect the availability and accuracy of wireless and 

satellite navigation and correction services (e.g. GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot 

guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to 

use Raven systems, or products used as components of systems, which rely upon the reception of these signals or 

availability of these services. Raven Industries accepts no responsibility for the use of any of these signals or 

services for other than the stated purpose.  

Summary of Contents for RG1300





























































Reviews: