background image

Propeller Owner's Manual 

136

 

INSTALLATION AND REMOVAL   

61-00-36 

Page 3-14 

Rev. 2 Feb/17

B.  Installation of a Metal Spinner Bulkhead on a Propeller Hub 

CAUTION:  

INSTRUCTIONS AND PROCEDURES 

IN THIS SECTION MAY INVOLVE 

PROPELLER CRITICAL PARTS. REFER 

TO THE INTRODUCTION CHAPTER 

OF THIS MANUAL FOR INFORMATION 

ABOUT PROPELLER CRITICAL PARTS. 

REFER TO THE ILLUSTRATED PARTS 

LIST CHAPTER OF THE APPLICABLE 

OVERHAUL MANUAL FOR THE 

IDENTIFICATION OF SPECIFIC 

PROPELLER CRITICAL PARTS.

(1)  Spinner installation must make sure of clearance in the 

following areas:
(a)  The spinner bulkhead must be spaced between the 

hub and the engine cowl to permit the spinner dome 

blade cut-out openings to clear the propeller blades 

at all blade angle locations. Refer to Figure 3-4.  
1

  The spinner bulkhead and any attached filler 

plate must also clear the propeller blades at all 

blade angle locations. Refer to Figure 3-4.

(b)  The edge of the spinner bulkhead and the installed 

spinner dome that faces the engine cowl must 

have space to clear the engine cowl and avoid 

interference during propeller/engine operation.  

Refer to Figure 3-4.

(c)  The hub clamping bolts on which the spinner 

bulkhead is attached must not be so long that the 

bolts interfere with the engine cowl during  

propeller/engine operation. Refer to Figure 3-4.
1  On some installations, it may be necessary to 

install spacer(s)/washer(s) between the head of 

each hub clamping bolt and the hub to move the 

threaded end of the bolt away from the engine 

cowl. Refer to Figure 3-4.

Summary of Contents for B-4270





































































































































































































































Reviews: