Hammond A-3 Playing Manual Download

Page: 174 / 180

HA<O>

XK-5

Owner’s Playing Guide

174

CUSTOM SETS LIST

CUSTOM TONE WHEELS

A-100, B-3, C-3

F1: Normal

Simulates the organ’s Tone Wheels with precision.

F2: Rumble less

Cut off the motor rumble by using high-pass filter.

F3: Mixture

Sounds leakage tones with harmonized.

Mellow

F1: Full Flats

Like the electronic organ, oscillates at flatly.

F2: Husky

Dips the middle frequency.

F3: Flute Lead

Boosts the middle frequency.

CUSTOM CONTACT

F1: B-3 A27563

Simulates the organ as above.

F2: Regular

Physical contact 1 sounds 8´, 2´, 1´
Physical contact 2 sounds 5-1/3´, 2-2/3´, 1-1/3´
Physical contact 3 sounds 16´, 4´, 1-3/5´

F3: Single

All the footages sounds at deepest physical contacts.

CUSTOM SUB DRAWBARS

F1: B-3 A27563
F2: B-3 #87396
F3: A-100 #33339

All the customs simulates the organs as above.

CUSTOM PIPES

Normal

A basic, general-purpose Pipe set.

No Chiff

Similar to Normal, but with reduced Chiff.

Heavy Detune

Pipe Voices intentionally detuned for a “chorus” effect.

CUSTOM CABINETS

122 Gentle

Simulates 122 cabinet (Large body, peaking horn driver) heard from a distance, rear.

122 Wild

Simulates 122 cabinet heard from closer, front.

31H-Type

Simulates 31H cabinet heard from a distance, rear.

147 Gentle

Simulates 147 cabinet (Large body, wide range) heard from a distance, rear.

147 Wild

Simulates 147 cabinet heard from closer, front.

145 Gentle

Simulates 145 cabinet (Middle body, slightly narrow range) heard from a distance, rear.

145 Wild

Simulates 145 cabinet heard from closer, front.

PR-40

Simulates a stationary speaker system.

Summary of Contents for A-3





















































































































































































Search results

Summary of Contents for A-3

Reviews:

Related manuals for A-3

Brands by name

Popular brands

Hammond A-3, Playing Manual

Search results

Summary of Contents for A-3

Reviews:

Related manuals for A-3

Brands by name

Popular brands