Haier YR-E17 Operation & Installation Manual Download | Manualshive

Page: 35 / 52

background image

34

Operation

(1) The main interface does not display malfunction.
(2) Under no screen saving state, press

key for 10

seconds to check all indoor units malfunction in the group, but
at this time, the interface does not display clock information
and timer information. Unit No. is displayed behind the top-left
colon; current malfunction is displayed before top-right colon
and historical malfunction is behind colon.
(3) Unit No. is displayed in decimal and malfunction is

displayed in hexadecimal.
(4) All hexadecimal numbers of malfunction are in capital. But
b and d is in small capital in order not to mix with 8.

(5) If there is no current malfunction, “--” is displayed before
the right colon; if there is no historical malfunction, “--” is
displayed behind the right colon.
(6) Press

key to quit malfunction check state. The clock

information and timer information are displayed.
(7) Malfunction records clearance: Keep pressing

key for

10 seconds, malfunction is displayed. Then press

key

again for 5 seconds to clear current and historical malfunction
of all the units.
(8) Press to choose unit No..

Malfunction Display

«
...
33
34
35
36
37
...
»

Summary of Contents for YR-E17





















































Reviews:

No comments

Related manuals for YR-E17

Brand: Dantherm Pages: 96

Brand: A1TECH Pages: 27

Brand: Canarm Pages: 3

Brand: D+H Pages: 14

Brand: EasyIO Pages: 18

Brand: Radionics Pages: 14

Omnicharge Solar OCS 100-20

Brand: tbs electronics Pages: 64

Brand: National Instruments Pages: 17

Brand: Davey Pages: 12

JetWeb JX2-PRN1

Brand: Jetter Pages: 25

Brand: Stanley FatMax Pages: 1

Brand: Parallel Audio Pages: 4

Brand: Elfa Pages: 22

Brand: Tripp Lite Pages: 40

Sundstrom SR307

Brand: S.E.A. Group Pages: 5

EAGLE CORE PLUS

Brand: PrimaLuceLab Pages: 40

Brand: EBS Pages: 118

IconRemote IR10A

Brand: X10 Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands