Haier YR-E17 Operation & Installation Manual Download | Manualshive

Page: 28 / 52

background image

27

Operation

When filter cleaning icon

is displayed, the icon will display

in function sequence. If filter cleaning icon is flashing, press

key to clear it.

Filter Cleaning

(1) Press

key to enter function setting, then press

to choose energy saving, press

key again to confirm the

operation and display energy saving icon

. If energy

saving function has been set, the above operation will cancel
it.
(2)The energy saving default parameter are 23°C (74°F) (the
lowest temp. limit of cooling and dry mode) and 26°C (78°F)
(the highest temp. limit of heating mode). The temp. adjusting
range is 23°C-30°C (74°F-80°F) in cooling and dry mode, the
temp. adjusting range is 16°C-26°C (60°F-78°F) in heating
mode. If energy saving function is set, the indoor units will run
at the default temperature.
Note: Fresh Air unit has no energy saving function.

Energy Saving

«
...
26
27
28
29
30
...
»

Summary of Contents for YR-E17





















































Reviews:

No comments

Related manuals for YR-E17

Brand: Radio Shack Pages: 52

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 26

Brand: NAiS Pages: 199

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 179

Brand: Panasonic Pages: 23

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 20

INDUSTRY PAN9028

Brand: Panasonic Pages: 34

Brand: Maestra Pages: 22

Brand: Jetter Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands