Haier YR-E17 Operation & Installation Manual Download

Page: 48 / 52

Wired Controller Wiring Instruction

C. Two wired controllers control one indoor unit. The wired

controller connected with indoor unit is called master
one, the other is called slave one. Master wired controller
and indoor unit; master and slave wire controllers are all
connected through 3 pieces of polar wire.

Communication wiring

Communication wiring length (m/

ft)

Dimensions of wiring

< 100m/328ft

0.3mm

x3-core shielded

wire (22AWG,3wire)

≥100m/328ft and <200m/656ft

0.5mm

x3-core shielded

wire (20AWG,3wire)

≥200m/656ft and <300m/984ft

0.75mm

x3-core shielded

wire (18AWG,3wire)

≥300m/984ft and <400m/1312ft

1.25mm

x3-core shielded

wire (16AWG,3wire)

≥400m/1312ft and <500m/1640ft

2mm

x3-core shielded wire

(14AWG,3wire)

*One side of the shielded sheet of communication wire must
be earthed.

Summary of Contents for YR-E17





















































Search results

Summary of Contents for YR-E17

Reviews:

Related manuals for YR-E17

Brands by name

Popular brands

Haier YR-E17, Operation & Installation Manual

Search results

Summary of Contents for YR-E17

Reviews:

Related manuals for YR-E17

Brands by name

Popular brands