Haier YR-E17 Operation & Installation Manual Download | Manualshive

Page: 41 / 52

background image

40

Operation

(8) The number about the static pressure grade and the static
pressure grade can also be queried/ changed by advanced
setting interface(Only valid for part of models).

(1) Press the SET key and key for 5s to enter the advanced
setting interface to inquire/adjust rated operation function.
Function A will be displayed in the temp. display area. The last
two 88 in the clock display area show the function code, and

the timing display area shows the specific information of the

current function.
(2) After entering the advanced setting, function A in the temp.
display area stays statically, and it can be changed by the
Fan key. The function code 01 displayed in the clock display

area flashes, which can be changed by the Up/Down key. The
specific information in the timing display area stays statically.
At this time press SET key to confirm. The function code
01 in the clock display area stays statically with the specific
information flashes in the timing display area, meaning the
specific information can be changed currently, press the Up/
Down key to change the content and the SET key to confirm.

Rated Operation Function (Only valid for part of models)

«
...
39
40
41
42
43
...
»

Summary of Contents for YR-E17





















































Reviews:

No comments

Related manuals for YR-E17

DELTAFLUX MT100

Brand: PIETRO FIORENTINI Pages: 16

Brand: Racal Instruments Pages: 94

Brand: Racal Instruments Pages: 97

Brand: Hanna Instruments Pages: 88

Brand: OES Pages: 3

Slim Remote Control

Brand: Packard Bell Pages: 2

Brand: Unipower Pages: 24

Brand: IBM Pages: 20

Brand: DAV TECH Pages: 24

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 16

Brand: SYR Pages: 2

Brand: Burlington Pages: 7

Brand: Mitsubishi Pages: 30

Brand: Hach Pages: 504

Brand: Fagor Pages: 8

Brand: bluelab Pages: 39

Brand: SOMFY Pages: 2

Brand: MT-Propeller Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands