Haier YR-E17 Operation & Installation Manual Download | Manualshive

Page: 46 / 52

background image

45

Operation

(1) Powered off in cooling mode, keep pressing “ON/OFF” key
for 10 seconds, it will enter into the forced cooling function,
and the cooling mode icon will be displayed on the interface.

“LL” is flashing in the temp. area at the same time. Press “ON/
OFF” key to power off and exit forced cooling.

(2) Powered off in heating mode, keep pressing “ON/OFF” key
for 10 seconds, it will enter into the forced heating function,
and the heating mode icon will be displayed on the interface,

“HH” is flashing in the temp. area at the same time. Press “ON/
OFF” key to power off and exit forced heating.
(3) All the keys are invalid except “ON/OFF” key under forced

cooling/heating mode, which can be cancelled by powering off

manually or receiving “trial operation” finished order from the

communication. The former one can operate power off directly
while the later one will make the controller do by following the
order.

Forced Cooling/ Heating

«
...
44
45
46
47
48
...
»

Summary of Contents for YR-E17





















































Reviews:

No comments

Related manuals for YR-E17

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

Brand: TA Hydronics Pages: 14

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: Danfoss Pages: 24

Brand: Jandy Pages: 28

Brand: Jands Pages: 6

PXI-6683 Series

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 29

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 7

FIELDPOINT FP-1600

Brand: National Instruments Pages: 21

FieldPoint FP-1001

Brand: National Instruments Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands