Haier YR-E17 Operation & Installation Manual Download | Manualshive

Page: 42 / 52

background image

41

Operation

(3) Rated operation including USA rated operation and
European rated operation can be inquired/adjusted through
function code 07 in the advanced setting. “00” means the
European rated operation, and “01” means the USA rated
operation.
(4) If the content of 07 is “00”, then press the Up/Down key to
switch to 08(Europe rated operation) directly, “09” will not in
the function code cycle, use the Up/Down key to adjust and

press the SET key to confirm .

(5) If the content of 07 is “01”, press the Up/Down key to
switch to 09(USA rated operation) directly. “08” will not in the
function code cycle. use the Up/Down key to adjust, and press

the SET key to confirm.

(6) When in the Europe rated operation situation, only rated
cooling condition(00-05) can be set in cooling mode; only rated
heating condition(00-04,06,07) can be set in heating mode. In
other modes, rated condition can’t be set.
(7) When in the USA rated operation situation, only rated
cooling condition(00-05)can be set in cooling mode; only rated
heating condition(00,06-11) can be set in heating mode. In
other modes, rated condition can’t be set.
(8) If the wired controller sets the rated operation function,
only wired controller can cancel it. If the remote controller sets
the rated operation function, the wired controller and remote
controller can both cancel it.

«
...
40
41
42
43
44
...
»

Summary of Contents for YR-E17





















































Reviews:

No comments

Related manuals for YR-E17

Brand: ABB Pages: 200

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

ServeRAID M5014

Brand: IBM Pages: 106

Brand: Oldham Pages: 32

Brand: H3C Pages: 14

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Frigolink FVB110B

Brand: WURM Pages: 4

Brand: Conel Pages: 52

Brand: Revox Pages: 57

Brand: Wittenstein Pages: 52

BNI EIP-502-105-R015

Brand: Balluff Pages: 274

WISE-224 Series

Brand: ICP DAS USA Pages: 8

Brand: SSHC Pages: 2

Brand: Bame Pages: 12

Brand: M-system Pages: 3

Brand: SMC Networks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands