background image

7

Section 1

Specifications

Specifications are subject to change without notice.

General

Dimensions

Height (lid closed): 130 cm (51 in.)
Height (lid open): 180 cm (71 in.)
Width 76 cm (30 in.)
Depth 81 cm (32 in.)
Weight 86 kg (190 lb)
Refer to 

Figure 1 on page 12

.

Cabinet

Low density polyethylene with UV inhibitor. Cabinet enclosure 
rated IP 24.

Temperature range

As is: 0 to 50 ºC

With AC battery back up: 0 to 40 ºC (32 to 104 ºF)

With optional controller compartment heater: -40 to 50 ºC (-40 
to 122 ºF)

With AC battery backup and controller compartment heater: 
-15 to 40 ºC (5 to 104 ºF)

Recovery time

Sampler temperature recovers to 4 ºC within 5 minutes after 
the door has been held open for one minute in 24 ºC (75 ºF) 
ambient environment while in an active cooling cycle.

Pull-down time

Air temperature drops from 24 ºC (75 ºF) to 4 ºC (39 ºF) within 
20 minutes (typical).

Thermal system

Top mounted compressor/condenser with fan forced air 
cooled condenser; 3 sided wrap-around evaporator plate; 
rigid foam insulation; microprocessor controlled thermostat 
maintains sample liquid at 4 °C (±1 °C); frost free; 
compression gasket door seal; air cooled condenser is 
protected against corrosion with a food grade epoxy; all 
exposed copper tubing is insulated to avoid sweating and 
condensation.

Operating environment

Installation category II

Pollution degree 2

Altitude 2000 m

Power requirements

115 VAC, 60Hz, 4.2A, or 6.4A with optional controller 
compartment heater.
230VAC, 50Hz, 2.7A, or 4.1A with optional controller 
compartment heater.

Optional ac Power Backup

Pump/Controller Only: Rechargeable 7 amp-hour gel lead 
acid battery takes over automatically with ac line power 
failure. Integral trickle charger maintains battery at full charge.

Internal battery 

Three AA alkaline batteries maintains program logic and real 
time clock for five years.

Control panel

21 key membrane switch keypad with 4 multiple function soft 
keys; 8 line x 40 character alphanumeric, back-lit 
liquid-crystal graphics display. Self prompting/menu driven 
program.

Data logging

Records program start time and date, stores up to 400 
sample collection times/dates, all program entries, 
operational status including number of minutes or pulses to 
next sample, bottle number, number of samples collected, 
number remaining, sample identification number, and all 
logged data (i.e. level, flow, pH, stream temperature, 
refrigerated compartment sample temperature, ORP, rainfall, 
and any externally logged data - up to 7 external channels). 
Also, up to 200 events are logged, including alarm conditions, 
program run/stop events, etc.

Goodnal STP ST041 Pre Treatment (Sigma 900 MAX All Weather Refrigerated Sampler) Vendor Manual

Q-Pulse Id VM373

Active 29/10/2013

Page 7 of 122

Summary of Contents for Sigma 900 MAX



























































































































Reviews:

Related manuals for Sigma 900 MAX