manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 35

Command Manual – MPLS Basics 
H3C S9500 Series Routing Switches 

Chapter 1  MPLS Basics Configuration Commands

 

1-27 

Default Level 

1: Monitor level 

Parameters 

interface-type interface-number

: Specifies an interface by its type and number. 

verbose

: Displays detailed information. 

Description 

Use the 

display mpls interface

 command to display information about a specified or 

all interfaces with MPLS enabled. 

z

 

If no parameters are specified, the command displays only the brief information 

about all MPLS-enabled interfaces. 

z

 

If you specify 

interface-type

 

interface-number

, the command displays the brief 

information about the specified MPLS-enabled interface. 

Related commands: 

display mpls statistics interface 

and 

mpls

. 

Examples 

# Display information about all interfaces with MPLS enabled. 

<Sysname> display mpls interface 

Interface   Status     TE Attr    LSP Count   CRLSP Count 

Vlan12      Up         En         0           0           

Vlan14      Up         En         0           0           

# Display detailed information about the specified MPLS-enabled interface. 

<Sysname> display mpls interface vlan-interface 12 verbose 

No             : 1 

Interface      : Vlan12 

Status         : Down 

TE Attribute   : Disable 

LSPCount       : 0 

CR-LSPCount    : 0 

FRR            : Disabled 

 

 

  Note: 

For information about FRR, refer to 

MPLS TE Configuration

 in the 

MPLS VPN Volume

. 

 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands