manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 171

Command Manual – MPLS TE 
H3C S9500 Series Routing Switches 

Chapter 1  MPLS TE Configuration Commands

 

1-80 

Examples 

# Reroute MPLS TE tunnel 0 to an available bypass tunnel in case the protected link or 

node that it traverses fails.  

<Sysname> system-view 

[Sysname] interface Tunnel 3/0/1 

[Sysname-Tunnel3/0/1] mpls te fast-reroute 

1.1.60  mpls te fast-reroute bypass-tunnel 

Syntax 

mpls te fast-reroute bypass-tunnel

 

tunnel tunnel-number

 

undo mpls te fast-reroute bypass-tunnel tunnel tunnel-number

 

View 

Interface view 

Default Level 

2: System level 

Parameters 

tunnel-number

: Bypass tunnel number. 

Description 

Use the 

mpls te fast-reroute bypass-tunnel

 command to specify a bypass tunnel for 

the protected interface. 

Use the 

undo mpls te fast-reroute bypass-tunnel

 command to remove the specified 

bypass tunnel. 

You may perform the 

mpls te fast-reroute bypass-tunnel

 command multiple times to 

specify multiple bypass tunnels for the protected interface. At present, a maximum of 

three bypass tunnels can be specified for a protected interface. 

When specifying a bypass tunnel, consider the following: 

z

 

The state of the tunnel must be up. 

z

 

The protected interface is not the outgoing interface in the route entries for the 

LSP of the bypass tunnel. 

 

 

  Note: 

A bypass tunnel cannot be used for services such as VPN at the same time. 

 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands