manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 108

Command Manual – MPLS TE 
H3C S9500 Series Routing Switches 

Chapter 1  MPLS TE Configuration Commands

 

1-17 

 Path and Resv message refresh interval: 30 sec 

 Path and Resv message refresh retries count: 3 

 Blockade Multiplier: 4 

Table 1-6 

Description on the fields of the 

display mpls rsvp-te

 command 

Field 

Description 

LSR ID 

Label switched Router ID, in the format of X.X.X.X 

Resv Confirmation Request 

Reserved confirmation request 

RSVP Hello Extension 

State of the hello mechanism: enabled or disabled 

Hello Interval 

Hello interval, in seconds 

Max Hello misses 

Maximum number of consecutive hello losses 
before a neighbor is considered dead 

Path and Resv message 
refresh interval 

Path and reservation message refresh interval, in 
seconds 

Path and Resv message 
refresh retries count 

Number of Path and Resv message retransmissions

Blockade Multiplier 

Blockade multiplier 

 

# Display the RSVP-TE configuration on interface VLAN-interface 12.  

<Sysname> display mpls rsvp-te interface vlan-interface 12 

Interface Vlan-interface 12 

 Interface state: UP 

 Total-BW: 80              Used-BW: 20 

 Hello configured: NO      Num of Neighbors: 1 

 SRefresh feature: ENABLE  SRefresh Interval: 30sec 

 Authentication: DISABLE   Reliability configured: NO 

 Retransmit Interval: 500msec  Increment Value: 1 

Table 1-7 

Description on the fields of the 

display mpls rsvp-te interface

 command 

Field 

Description 

Interface Vlan-interface 12

RSVP-TE enabled interface 

Interface state 

Physical interface state 

Total-BW 

Total bandwidth (in kbps) 

Used-BW 

Used bandwidth (in kbps) 

Hello configured 

State of the hello mechanism: enabled or disabled 

Num of Neighbors 

Number of neighbors connected to the interface  

Srefresh feature 

State of the summary refresh function: enabled or 
disabled 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands