H3C S9500 Series Command Manual Download Page 26

Page: 26 / 350

Command Manual – MPLS Basics
H3C S9500 Series Routing Switches

Chapter 1 MPLS Basics Configuration Commands

1-18

------------------------------- End of Debug Info--------------------------

// Entry content.

*0.21331197 PE1 LSPAGENT/8/Event:

Agent-MFW: Return value of Call MPLSFW_AgentSendMsgForLspm API

function,return VOS_OK!

// Add the entry successfully.

# Enable MPLS interface debugging by executing the

debugging mpls

management

interface

command.

Start two switches, connect the two switches, and configure MPLS and MPLS LDP for

them to establish a session between them. Enable MPLS interface debugging by

executing the

debugging mpls management interface

command on one switch while

executing the

reset mpls ldp all

command on the other.

<PE1>debugging mpls management interface

*0.22430627 PE1 LSPM/8/LSPM INTERFACE:

Received Signal DELETE message, VRF Index: 0 destination: 0x8c010101

destination mask: 0xffffffff Nexthop: 0x7f000001 OutIfIndex: 0x150000

InIfIndex: 0x300010

// The interface receives a Signal DELETE message.

*0.22430627 PE1 LSPM/8/LSPM INTERFACE:

Received Signal DELETE message, VRF Index: 0 destination: 0x8c030303

destination mask: 0xffffffff Nexthop: 0x8c0c0102 OutIfIndex: 0x300010

InIfIndex: 0x0

// The interface receives a Signal DELETE message.

#Dec 22 16:22:17:972 2005 PE1 LDP/5/SessionUp: Session(140.2.2.2:0. public

Instance)'s state change to Up

// The Session is Up again.

*0.22435678 PE1 LSPM/8/LSPM INTERFACE:

Received Route CREATE message, destination: 0x8c010101 destination mask:

0xffffffff.

# Enable debugging for the policy whereby LDP establishes LSPs by executing the

debugging mpls

management policy

command.

Start two switches, connect the two switches, and configure MPLS and MPLS LDP for

them to establish a session between them. Enable debugging for the policy whereby

LDP establishes LSPs by executing the

debugging mpls management policy

command on one switch while executing the

reset mpls ldp all

command on the other.

<PE1>debugging mpls management policy

<PE1>

#Dec 23 10:12:18:552 2005 PE1 LDP/5/SessionDown: Session(140.2.2.2:0. public

Instance)'s state change to Down

Summary of Contents for S9500 Series































































































































































































































































































































































Search results

Summary of Contents for S9500 Series

Reviews:

Brands by name

Popular brands

H3C S9500 Series, Command Manual

Search results

Summary of Contents for S9500 Series

Reviews:

Brands by name

Popular brands