manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 14

Command Manual – MPLS Basics 
H3C S9500 Series Routing Switches 

Chapter 1  MPLS Basics Configuration Commands

 

1-6 

*0.19215421 PE1 LDP/8/Session: Vlan-interface 12 

 Sent keep alive message to LSR: 140.2.2.2. 

// Send a Keepalive message. 

*0.19215421 PE1 LDP/8/Session: Vlan-interface 12 

 Session(140.2.2.2)'s state changed from Initialised to Open received. 

// The session’s state is changed. 

#Dec 22 15:32:43:437 2005 PE1 LDP/5/SessionUp: Session(140.2.2.2:0. public 

Instance)'s state change to Up  

// Display a Session-UP Trap message. 

*0.19215437 PE1 LDP/8/Session: Vlan-interface 12 

 Session(140.2.2.2) received keep alive message on Open Received state. 

// Receive a Keepalive message. 

*0.19215437 PE1 LDP/8/Session: Vlan-interface 12 

 Session(140.2.2.2)'s state changed from Open received to operational. 

// The session’s state is changed to Operational. 

*0.19215437 PE1 LDP/8/Session: 

 Address message sent to LSR: 140.2.2.2 

// Send an address message to the opposite end. 

*0.19215437 PE1 LDP/8/Session: 

 Informed Session Up event to L2VPN  

// Inform L2VPN of Session UP. 

*0.19215437 PE1 LDP/8/Session: Vlan-interface 12 

 Session(140.2.2.2) received address message on Operational state. 

// Receive an address message. 

*0.19216438 PE1 LDP/8/Session: 

 Session(140.3.3.3) received keep alive message on Operational state. 

// Receive a Keepalive message. 

# Enable PDU packet event debugging by executing the 

debugging mpls

 

ldp pdu

 

command. 

Start two switches, connect the two switches, and configure MPLS and MPLS LDP for 

them to establish a session between them. Execute the 

debugging mpls

 

ldp pdu

 

command on one switch. 

<PE1>debugging mpls ldp pdu 

<PE1> 

*0.19804957 PE1 LDP/8/PDU: 

 Receive UDP Message from Peer: 140.3.3.3. Message content: 

 01 00 00 1c 00 00 17 bf 04 00 00 04 00 2d c0 00 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands