manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 345

Command Manual – GRE 
H3C S9500 Series Routing Switches

 

Chapter 1  GRE Configuration Commands

 

1-8

 

View 

Any view 

Default Level 

1: Monitor level 

Parameters 

number

: Tunnel interface number, in the format of board slot number/0/Tunnel interface 

number. 

Description 

Use the 

display ipv6 interface tunnel

 command to display IPv6 information about a 

tunnel interface, including the Tunnel interface link status, IPv6 status, IPv6 addresses 

of the Tunnel interfaces, etc. 

Examples 

# Display IPv6 information about interface Tunnel 3/0/0. 

<Sysname> display ipv6 interface tunnel 3/0/0 

Tunnel3/0/0 current state :UP 

Line protocol current state :UP 

IPv6 is enabled, link-local address is FE80::101:101 

  Global unicast address(es): 

    2002:101:101::1, subnet is 2002::/16 

  Joined group address(es): 

    FF02::1:FF01:101 

    FF02::1:FF00:1 

    FF02::2 

    FF02::1 

  MTU is 1500 bytes 

  ND reachable time is 30000 milliseconds 

  ND retransmit interval is 1000 milliseconds 

  Hosts use stateless autoconfig for addresses 

Table 1-4 

Description on the fields of the 

display ipv6 interface tunnel

 command 

Field 

Description 

Tunnel3/0/0 current state: UP 

Status of the physical layer of the tunnel interface 
is  UP  

Line protocol current state: UP

Status of the link layer of the tunnel interface is UP 

IPv6 is enabled 

IPv6 is enabled on the tunnel interface 

link-local address 

Link-local address of the tunnel interface 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands