h/p/cosmos Arsalis Gaitway 3D Service Manual Download Page 3

Page: 3 / 108

gaitway-3D Service manual

Ref.:TM-MAN-0005-ARS

Iss.: A

Rev.: 9

Date: 07/12/2020

Page : III

TABLE OF CONTENTS

Model overview .................................................................................................... 1

1.1.

Options and accessories .............................................................................. 2

Introduction .......................................................................................................... 4

2.1.

Description .................................................................................................... 4

2.2.

Device components, including software and accessories ............................. 4

2.2.1.

Treadmill components ........................................................................... 4

2.2.2.

Treadmill supports ................................................................................. 5

2.2.3.

Force sensor units ................................................................................. 6

2.2.4.

Amplifier ................................................................................................ 6

2.2.5.

gaitway-3D software .............................................................................. 7

2.3.

Safety equipment .......................................................................................... 7

Safety notes, warnings, precautions .................................................................... 8

3.1.

General ......................................................................................................... 8

3.2.

Room conditions and environmental requirements ....................................... 8

3.3.

Transport and installation ............................................................................. 9

3.4.

Storage ....................................................................................................... 10

3.5.

Device care ................................................................................................. 10

3.6.

Service safety aspects ................................................................................ 11

How to use this manual ..................................................................................... 11

Installation and commissioning .......................................................................... 11

5.1.

gaitway-3D unpacking ................................................................................ 12

5.2.

Treadmill support assembly ........................................................................ 12

5.3.

gaitway-3D floor fixation ............................................................................. 12

5.4.

gaitway-3D final assembly .......................................................................... 14

5.5.

gaitway-3D startup ...................................................................................... 14

gaitway-3D sensors calibration .......................................................................... 14

gaitway-3D on-site check-out ............................................................................ 16

Amplifier replacement ........................................................................................ 16

Load cell replacement ........................................................................................ 16

10.

Amplifier fuse replacement ............................................................................. 16

11.

Installation equipment .................................................................................... 17

12.

Installation and commissioning checklist ........................................................ 19

12.1.

gaitway-3D unpacking ............................................................................. 19

12.2.

Treadmill support assembly .................................................................... 20

12.3.

gaitway-3D floor fixation .......................................................................... 24

12.4.

gaitway-3D final assembly ...................................................................... 27

12.5.

gaitway-3D startup .................................................................................. 54

12.6.

Installation and commissioning summary sheet ...................................... 57

13.

gaitway-3D sensors calibration checklist ........................................................ 58

13.1.

Sensors calibration summary sheet ........................................................ 67

14.

gaitway-3D on site check-out checklist .......................................................... 68

14.1.

On-site checkout summary sheet ............................................................ 74

15.

Amplifier replacement checklist ...................................................................... 75

15.1.

Force amplifier dismounting and packing ................................................ 75

15.2.

Force amplifier installation ...................................................................... 79

15.3.

Amplifier replacement summary sheet .................................................... 83

Summary of Contents for Arsalis Gaitway 3D













































































































Search results

Summary of Contents for Arsalis Gaitway 3D

Reviews:

Related manuals for Arsalis Gaitway 3D

Brands by name

Popular brands

h/p/cosmos Arsalis Gaitway 3D, Service Manual

Search results

Summary of Contents for Arsalis Gaitway 3D

Reviews:

Related manuals for Arsalis Gaitway 3D

Brands by name

Popular brands