GW Instek GDS-1000B Series Programming Manual Download Page 222

Page: 222 / 259

GDS-1000B Programming Manual

222

:CHANnel<X>:LABel:DISPlay

Description

Turns the label on/off for the selected channel or
returns its status.

Syntax

:CHANnel<X>:LABel:DISPlay { OFF | ON | ? }

Related
commands

:CHANnel<X>:LABel

Parameter

<X>

Channel 1, 2, 3, 4

OFF

Turns the file label off for the selected
channel.

Turns the file label on for the selected
channel.

Return parameter

Returns the status of the file label for the selected
channel (ON, OFF).

Example

:CHANnel1:LABel "CH1"
:CHANnel1:LABel:DISPlay ON
:CHANnel1:LABel:DISPlay?
ON

Sets the channel 1 label to "CH1" and then turns
the label display on. The query return shows that
the label is on.

:REF<X>:LABel

Description

Sets or returns the file label for the selected
reference waveform.

Syntax

:REF<X>:LABel {<string> | ?}

Related
commands

:REF<X>:LABel:DISPlay

Set

Query

Set

Query

Summary of Contents for GDS-1000B Series




































































































































































































































































Search results

Summary of Contents for GDS-1000B Series

Reviews:

Brands by name

Popular brands

GW Instek GDS-1000B Series, Programming Manual

Search results

Summary of Contents for GDS-1000B Series

Reviews:

Brands by name

Popular brands