GST GST-IFP8 Installation And Operation Manual Download Page 56

Page: 56 / 66

GST-IFP8 Intelligent Fire Alarm Control Panel

Installation and Operation Manual

Page 46

Chapter 8 Maintenance

The FACP shall only be repaired by specially trained GST technical service

personnel. Please disconnect the power before repair!

Warning: The key to the FACP shall be kept by specially assigned maintenance

personnel!

8.1 Replacing the Battery

Type of battery: Sealed lead-acid battery

Recommended period for replacing the battery: 5 years (25

℃

)

Recommended manufacturer and model: Yuasa/NP38-12I

Disposal of used batteries: Please properly dispose the used batteries according to

your local rules and regulations.

NOTE:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT

TYPE.

8.2 Replace of Fuse

Position

Mark

Rating

Power filter F7.820.323

2A delay

8.3 Troubleshooter

No. Problems

Possible Causes

Solutions

No indication on
the panel or
abnormal
indication

a. Power is abnormal
b. Loose connection with

switchboard.

a. Check and replace

low-voltage switch power.

b. Check the connection to

display board.

Display “AC
Fault” after
power-up.

No AC power

Check and connect AC wire.

isplay “Battery

Fault” after
power-up.

a. Loose connection with

battery.

b. Battery discharged or

damaged.

a. Open the power box and

check relative parts.

b. Power up for more than eight

hours with the AC power
supply, if the fault still exists,
replace the batteries.

Unable to register
loop equipment

Bus wrong or loose
connection

Check the loop

Unable to register
repeater panels

Wrong or loose connection
of communication cables

Check power supply to repeaters
and communication wires

Cannot print

a. Print mode is disabled.
b. Loose connection with

printer.

c. Printer damaged

a. Enable the print mode.
b. Check and connect the printer

well.

c. Replace the printer.

Equipment fault

a. Equipment

disconnected.

b. Equipment damaged.

a. Check connection
b. Replace equipment

Loop fault

Loop is shorted

Check the loop and repair.

Clock or memory
fault.

a. External interference.
b. Corresponding parts

are aging.

a. Check if the FACP is properly

earthed.

b. Inform our technical service

Summary of Contents for GST-IFP8



































































Search results

Summary of Contents for GST-IFP8

Reviews:

GST GST-IFP8, Installation And Operation Manual, Page: 56 / 66

Search results

Summary of Contents for GST-IFP8

Reviews: