GST GST-IFP8 Installation And Operation Manual Download Page 17 | Manualshive

Page: 17 / 66

GST GST-IFP8 Installation And Operation Manual Download Page 17

GST-IFP8 Intelligent Fire Alarm Control Panel

Installation and Operation Manual

Page 7

3.3.5 Sounder Strobes

Addressable

sounder strobe is a kind of audible/ visual alarm device installed in the

protected area, which can be activated by the FACP at the fire control center or by

manual call points. A series of GST addressable sounder strobes (such as I-9403) can

be connected to the loop of GST-IFP8. After activated, it will generate strong audible/

visual alarm signal.

3.3.6 Repeater Panel

GST852RP Repeater Panel is designed with a microprocessor. When one or more

detectors alarm fire, the repeater panel can display the location and alarm message of

the detectors with audible and visual signals. Through communication loops, it can be

connected with FACPs, disposing and displaying the data from the FACPs. When

monitoring several floors or several zones with one fire alarm control panel, a repeater

panel on each floor or in each zone can replace zonal fire alarm control panel.

(Note: IFP8 panel can not be used as the power source of Repeater Panel

GST852RP)

3.4 Defining Tool

The software is used for editing and downloading definition of device and C&E equation.

Before the system starts operation, you need to define the device and C&E using this

software on a computer, and then download them to the FACP.

«
...
15
16
17
18
19
...
»

Summary of Contents for GST-IFP8



































































Reviews:

No comments