GSS HDE 166 Assembly Instruction Manual Download Page 2

Page: 2 / 27

- 2 -

HDE 166

ontents

1 Safety regulations .......................................................................................3
2 General information ....................................................................................4

2.1 Scope of delivery ..........................................................................4

2.2 Meaning of the symbols used ..........................................................4

2.3 Technical data ...............................................................................4

2.4 Description ...................................................................................5

3 Installation ..................................................................................................6

3.1 Installing the Encoder module ..........................................................7

3.2 Connecting the Encoder module ......................................................8

3.3 EMC regulations ............................................................................8

4 The control panel at a glance .......................................................................9

4.1 Functions of the control panel buttons ...............................................9

4.2 Menu items ...................................................................................9

5 Programming ............................................................................................10

5.1 Programming procedure ...............................................................10

5.2 Programming the module ..............................................................12

Selecting the module / channel strip ..............................................13

Ethernet parameters .....................................................................13

IP address of the cassette .........................................................14

Address range (subnet mask) ...................................................14

Address of the gateway ..........................................................15

UDP port ...............................................................................15

IP output signal ............................................................................16

Output IP address ...................................................................17

Destination MAC address ........................................................17

Transmission protocol / Port number .........................................18

Quantity of data packets .........................................................19

Forward error correction / Transmission channel .......................19

Transport stream ID and ORGNET ID ........................................20

Input parameter ...........................................................................20

Data rate of the video signal ....................................................21

TV standard ...........................................................................21

Aspect ratio ...........................................................................22

Sharpness ..............................................................................22

Audio signal type and bit rate ..................................................22

Level of the audio signal ..........................................................23

Programme number (SID - Service ID) ........................................23

Channel name .......................................................................24

Factory reset ...............................................................................24

Saving settings ...........................................................................25

6 Final procedures ........................................................................................26

Summary of Contents for HDE 166




























Search results

Summary of Contents for HDE 166

Reviews:

Related manuals for HDE 166

Brands by name

Popular brands

GSS HDE 166, Assembly Instruction Manual

Search results

Summary of Contents for HDE 166

Reviews:

Related manuals for HDE 166

Brands by name

Popular brands