GSS HDE 166 Assembly Instruction Manual Download Page 24

Page: 24 / 27

- 24 -

HDE 166

hannel

na me

In this menu the channel name of the input can be set.

AV 1

…4

PROG 1

NAME

• Use the

buttons to select the digit of the channel name to be set and

use

buttons to set the desired character (" ", "0…9", "A…Z", "Ä",

"Ö", "Ü", "a…z", "ä", "ö", "ü", "+", "-", "/", ":" or "*").

• Press the button.

—> Return to the main menu "Input parameter"

• Use the

buttons to select the 2nd AV input and carry out its settings

analogous to that of the 1st AV input,

• Press the button.

—> The "Factory reset" – "

FACTORY Defaults

" main menu is activated.

aCtory

reset

In this menu you can reset all settings to the factory defaults.

Bx 2
Defaults

FACTORY

Bx 2

STORE

FACTORY

=> S

• Press the button.

—> The factory defaults are invoked (

"FACTORY STORE"

—> By pressing the

button, you will be returned to the main menu

"Selecting the module" (page 13).

• Press the button.

Summary of Contents for HDE 166




























Search results

Summary of Contents for HDE 166

Reviews:

Related manuals for HDE 166

Brands by name

Popular brands

GSS HDE 166, Assembly Instruction Manual

Search results

Summary of Contents for HDE 166

Reviews:

Related manuals for HDE 166

Brands by name

Popular brands