background image

Reverse osmosis system 

AVRO 125 TS/TL

 

 

 

 

Order no. 185 752 945-inter   Edited by:  nkes-mrie   G:\BA-752945-INTER_185_AVRO_125.DOCX 

16 

3 | Intended use 

 

The reverse osmosis system AVRO 125 TS/TL is used for 
demineralising drinking water. The water is primarily used for 
industrial applications. 

The permeate capacity of the system depends on the temperature 
and is defined at 15 °C. The permeate outputs can fall (falling 
temperature) or rise (rising temperature) by up to 3 % for each °C rise 
or fall in the feed water temperature.  

The system is adjusted to the permeate requirements to be expected 
at the installation site, it is not suitable for major deviations.  

Only operate the system if all components are properly installed. 
Safety devices and equipment must NEVER be removed, bridged or 
tampered with. 

Appropriate application of the device also implies that the information 
contained in this operation manual and all safety guidelines applying 
at the installation site be observed. Furthermore, the maintenance 
and inspection intervals have to be observed. 

 

3.1

 

System shutdown 

 

If the system is shut down for more than 14 days, the reverse 
osmosis system must be preserved by Grünbeck's technical customer 
service/authorised service company. The maximum time, the system 
can remain in the preserved condition is 6 months.  

In case the down time is longer, the system must be preserved 
again in regular intervals by Grünbeck's technical customer 
service/authorised service company. Prior to resuming operation, 
the preserving agent must be flushed from the system. 

 

Summary of Contents for AVRO 125 TL




























































Reviews: