GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 93

Page: 93 / 172

NP30A or NP40A

Table of Contents

Index

Adjustments

2019-03-11

Table of Contents

Index

407-502M

Adjusting the Weight-Transfer

Refer to Figure 66

1. In field conditions, unfold (page 59), lower applicator

(page 50), and set or check application depth

(page 96).

2. Pull forward to put coulters in ground.
3. Put tractor in Park and set parking brake.
4. Open weight-transfer shut-off valve .
5. Release the bypass valve lock disc . Turn the

bypass valve knob fully clockwise to shut-off all

bypass oil flow. Tighten lock disc.

6. Set tractor to half throttle. Adjust tractor flow control

valve so that wings fold/unfold at a reasonable

speed. Keep tractor running for step 7 through

step 10.

Note: On 2-point applicators, fold and unfold are followed

by lift and lower operations.

7. Set tractor remote circuit for unfold. Lock lever for

continuous operation.

8. At the pressure reducing valve , release the lock

disc .

9. Adjust the knob for an initial value of 800 psi on

the gauge . Tighten the lock disc.

10. At the bypass valve , release the lock disc .

Adjust the bypass valve knob counter-clockwise until

the pressure reading just begins to fall from the value

set at step 9. Turn the knob clockwise

turn.

Tighten the lock disc.

11. Observe applicator operation, and re-adjust

down-pressure as necessary after oil warm-up.

Repeat step 7 through step 10. The bypass valve

needs to be closed prior to any adjustment to

increase weight transfer.

Figure 66

Weight Transfer Adjustment

32041

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands