GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 72

Page: 72 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

Nurse Tanks

Use nurse tanks with proper current safety certification,

and current safety equipment and features.
Consult with your anhydrous ammonia supplier for safety

information and correct safe handling, transport and use

of anhydrous ammonia.
Consult with local and regional authorities on safe and

legal use of anhydrous ammonia, including emergency

and environmental contacts, and release reporting

requirements.
Review any decals and manuals available for your nurse

tank cart, and for any of its components. There may be

separate manuals for the tank, running gear, indicators,

valves and fittings.

This (Nutri-Pro

applicator) manual covers typical

operations for a representative NH

nurse tank cart.

Your cart is likely to vary. See the “

Using Anhydrous

Ammonia Safely

” manual (407-551M) for further

information about nurse tank carts.

Safing Applicator Before Cart Hitch

Close Line Valves

1. If any emergency shut-off valve

is open, use the

rope to close it. This also tests the rope and path.

Refer to Figure 59

2. Close solenoid valves:

a. Set console MASTER switch OFF
b. Set BOOM 1 BOOM 2

and BOOM 3

switches

OFF.

c. Turn POWER switch ON.

If the valves were open, setting either MASTER

or all BOOM switches off closes the On/Off

Valve

d. Wait 10 seconds.

The Control Valve

goes to minimum due to

zero speed. It does not completely close.

e. Set POWER switch OFF.

a. If the applicator has a single-section boom, only switch

BOOM 1 needs to be operated.

Figure 50

Nurse Tank Cart

31672

Figure 51

Applicator NH

Shut-Off Valve

31528

A18

A31

A30

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Brands by name

Popular brands