GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 130

Page: 130 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Maintenance and Lubrication

126

Bleeding Fold Hydraulics

Normally the fold hydraulics are bled at the factory

before shipping, and bleeding should not be required.
1. Connect the fold circuit to a hydraulic source, such

as a tractor remote.

2. Set the source circuit to Float to relieve any pressure

in the lines.

3. Disconnect both base and rod ends of all fold

cylinders.

4. Support the cylinders with ports facing up, and with

cylinders oriented so that rods cannot strike

applicator parts when at full extension.

5. Orient cylinders with base ends higher than rod

ends. Set circuit to Neutral.

One cylinder at a time:
6. Crack (slightly loosen) a JIC connection at a fold

cylinder base end.

7. Extend the circuit slowly until fluid appears at the

fitting.

8. Set the circuit to Neutral. Tighten the fitting.
9. Repeat step 6 through step 8 for the remaining

cylinders.

10. Retract the fold cylinders. Set circuit to Neutral.
11. Orient cylinders with rod ends higher than base

ends.

One cylinder at a time:
12. Crack (slightly loosen) a JIC connection at a fold

cylinder rod end.

13. Extend the circuit slowly until fluid appears at the

fitting.

14. Set the circuit to Neutral. Tighten the fitting.
15. Repeat step 12 through step 14 for the remaining

cylinders.

16. Set circuit to Float.
17. Re-pin base and rod ends of cylinders to center

section and wing lugs.

18. Test fold function carefully.

Crushing and Equipment Damage Hazards:

Bleed after servicing fold cylinders or their hoses. Air in the
system makes it hazardous to fold the applicator. If it is

necessary to service fold hydraulics while folded, the first

unfold is especially dangerous. Wing motion can be uneven or
jerky in fold. Unfolding wings could fall suddenly. Anyone

nearby could be seriously injured or killed. Equipment damage

is likely.

High Pressure Fluid Hazard:

Wear safety goggles and gloves. The bleed procedure requires
partially opening pressurized hydraulic lines. Escaping fluid

under pressure can penetrate the skin, causing serious injury.

If an accident occurs, seek immediate medical assistance from
a physician familiar with this type of injury.

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands