manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Share
Download
GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 84

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

80

Unhitching Nurse Tank

The procedure is different for exchanging tanks vs.

concluding application.

Exchanging Nurse Tanks

Consult with the nurse tank supplier, and all nurse tank

documents, before unhitching or exchanging tanks.
a. Suspend NH

3

 application per “

Suspending 

Application

” on page 76.

The purpose of this step is to minimize atmospheric 

NH

3

 vapor while working at the rear hitch. You may 

not be able to conduct all unhitching and re-hitching 

steps from up-wind of all the knives or tines.

b. Position the applicator cross-wind, with the wind 

from the right, knives or tines in ground.

c. Use the rope to close the emergency shut-off valve.
d. Put on your goggle and rubber gloves.
e. Shut off the nurse tank withdrawal valve

. Leave 

the nurse tank hose valves (

, if any), open.

f.

From up-wind, and with the orifice facing away from 

you, slowly open the breakaway coupler inlet bleed 

valve

.

g. Stand clear and wait for the hoses to discharge.
h. From the up-wind side, unscrew the nurse tank hose 

outlet coupler

. Secure the hose using whatever 

means the cart provides.

i.

Close all opened bleed valves.

j.

Release the nurse tank safety chains.

k. Remove the nurse tank hitch pin.

Final Nurse Tank Unhitch

a. Conclude NH

3

 application per “

Stopping 

Application

” on page 77.

The purpose of this step is to minimize atmospheric 

NH

3

 vapor while working at the rear hitch, because 

you may not be able to conduct all unhitching steps 

from up-wind of all the knives or tines.

b. From the up-wind side, unscrew the nurse tank hose 

outlet coupler (

on page 21).

c. Secure the outlet coupler with the nurse tank’s Acme 

parking plug.

d. Close all opened bleed valves.
e. Release the nurse tank safety chains.
f.

Remove the nurse tank hitch pin.

g. Remove nurse tank from behind applicator.

Control Variation Hazard:

If you are using multiple nurse tanks, study each one

separately. Unless they are owned by you, and known to be
identical, there is a high probability that there are differences

between them, even if they are all from the same terminal.

A65

A60

A13

A57

A57

Summary of Contents for Nutri-Pro NP30A













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands