manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Share
Download
GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 50

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

46

Pull-Type Applicators

Refer to Figure 25

To install cylinder stops:
1. Fully raise applicator (page 50). Set lift circuit to

Neutral.

2. Remove lock channel  from storage location.
3. Place a lock channel on the lift cylinder rod of each

cylinder to be locked.

4. Re-install locking pin and secure with cotter pin.
5. Install center section wheel lock channels.
6. Lower fertilizer applicator onto lock channels.
7. Set lift circuit to Float.

Front Caster Wheel Lock Channels

In routine use, install only the center section locks. For

maintenance, install all four. Installing the left wing lock

requires disabling the hydraulic depth stop.

Falling Hazard:

Do not climb or stand on tires or wheels. Even at full extension

on level ground, tires may not be in firm ground contact. They
could spin without warning. A fall could result in serious

injury.

Refer to Figure 26 and Figure 27

To install cylinder stops:
1. Fully raise applicator (page 50). Set lift circuit to

Neutral.

2. Install lift-assist locks.
3. At each section lift cylinder to be locked, remove

cotter pin and lock pin. Remove lock channel  from

storage location.

Figure 25

Lift-Assist Cylinder Lock Channel 

(Pull-Type)

38821

1

Figure 26

Front Caster Cylinder Lock Channel

38820

1

1

1

Summary of Contents for Nutri-Pro NP30A













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands