manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Share
Download
GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 30

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Metering Overview

26

The following callouts are for trailing nurse tank cart 

components. See the “

Using Anhydrous Ammonia 

Safely

” manual (407-551M) for all nurse tank callouts 

(

-

). The present manual lists only those required 

for applicator field operations.

A56.Acme Parking Plug

A threaded stud (or other means) for storage of the 

outlet hose when not coupled to the applicator.

A57.Acme Female Hose Coupler

This end of the hose connects the tank withdrawal 

valve

 to the leading applicator inlet

 at the 

breakaway coupler. For use with a Nutri-Pro

®

 

applicator, the outlet end of the hose must be 

equipped with a 1

3

/

4

-4 female Acme fitting.

The outlet end of the hose has a swivel collar

a

 or 

shroud containing the female Acme fitting. This 

allows connection without needing to twist the hose.

Acme hose couplers are intended for hand 

tightening only. Do not use tools to make the 

cart-applicator connection. A liquid-tight seal is 

made by the gasket in the male Acme fitting on the 

applicator break-away coupler.

A58.Outlet Hose Assembly

The hose may have zero, one or two operating 

valves

, one or more bleed valves

, and a 

hydrostatic relief valve

. The outlet end may 

have an Acme. plug.

A60.Hose Valve(s)

The hose may have zero, one or two operating 

valves

.

Excess NH

3

 Release Hazard:

If the outlet hose is entirely dismounted (both ends free) 

for transport and storage, and both ends are 1

3

/

4

-4 Acme, 

be sure about which end is which. Installing a hose 
backwards can result in needless excess NH

3

 release at 

unhitching, or a line segment unprotected by bleed and/or 

relief valves.

a. Acme collars may be aluminum, but all internal coupler components must be NH

3

-safe, typically stainless steel.

A51

A86

A63

A12

Hose valves are typically hand wheel valves, or 

lever valves. Read any documents provided for the 

valves. Have the terminal or dealer explain how the 

valves work.

Suffocation, Blinding and Burning Hazards:

Never test an anhydrous ammonia hose valve unless you 

are absolutely certain the hose and valve bodies are 
empty, or both hose ends are securely connected to sealed 

systems.



A two-valve hose can contain a substantial amount 

of NH

3

 even when completely disconnected. See 

“Avoid Line Traps

” on page 113

.



Older ball valves can contain NH

3

 inside the ball 

when closed, even though disconnected at both ends. 
See “

Avoid Ball Traps

” on page 114.

Follow instructions for bleeding and checking. Never use
a valve handle as a carrying handle. Keep hands clear of
bleed valves when carrying a hose.

Excess NH

3

 Release and Trapping Hazards:

Understand hose and tank withdrawal valve functions and 

sequencing. This manual presumes a hose with a single 
outlet-end shut-off valve

, and a tank outlet with a 

withdrawal valve

. If the hose in use is different, have 

the hose provider explain the correct order for operations.

A60

A61

A62

A60

A60

A65

Summary of Contents for Nutri-Pro NP30A













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands