manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Share
Download
GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 68

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

64

Unfolding 2013+ 5-Section (Parking, Storage,

Service)

To unfold, off field, for parking, storage or servicing,

unfold with the center section fully raised.
1. Hitch to a suitable tractor (page 30).
2. Retract the fold/lift circuit to fully raise the applicator

lift-assist.

3. Raise the tractor 3-point hitch.
4. If lift-assist lock channels are not installed, set

circuits to Neutral. Shut off the tractor. Remove

spacers (page 38). Install lock channels (page 45).

Re-start the tractor.

5. Remove the wing lock pins (page 47).

Refer to Figure 45

6. Set the Fold switch to

FOLD / UNFOLD

7. Extend the fold/lift circuit to unfold the wings.
8. Set all circuits to Neutral.
9. Shut off the tractor.
10. Unless using blocks or stands under wings, fully

extend wing gauge wheels (page 86).

11. Deploy parking stands at desired or maximum

height.

12. Start the tractor. Lower the 3-point hitch until the

applicator rests on the parking stands at front.

13. If wings stop above horizontal, move switch to FIELD

position, and Extend fold/lift to further unfold.

14. Extend until the gauge wheels contact the ground or

the wings stop. Set the fold/lift circuit to Float.

Notes about normal unfold:

• Inner wings unfold first. The outer wings are

constrained by the wing latches (page 48).

• Outer wings unfold last. The wing latches release

just before the inner wings are level.

• Wings do not unfold to below wings-level.

Machine Damage Risk:

Set the switch to UNFOLD. If set to PARK or FIELD, the
wings may unfold to below level and drag inward on the

ground.

Figure 45

Switch for Final Unfold

34918

Figure 46

Normal Unfold Sequence

34920

Summary of Contents for Nutri-Pro NP30A













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands