GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 47

Page: 47 / 172

NP30A or NP40A

Table of Contents

Index

Preparation and Setup

2019-03-11

Table of Contents

Index

407-502M

Wash Water

Refer to Figure 23

Empty the 10 gallon applicator First Aid Water tank. Refill

it with fresh clean water. If the nurse tank cart is at hand,

refill the nurse tank wash water as well.
The water needs to be changed daily. Water absorbs

ammonia vapor from the air, and becomes an

ammonium hydroxide solution over time.

When emptying wash tanks, use the time and water to

train operators on tank operations, and first aid rinsing

procedures.

Sealer Setup (Option)

As shipped from the factory, sealers are preset for

optimal shipping configuration. The factory default

settings are not likely to be suitable for your field

conditions.
Adjustments may also be required for different fields and

from season to season.
See “

Sealer Adjustments

” on page 102.

Figure 23

First Aid Water Station

31599

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Brands by name

Popular brands