GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 127

Page: 127 / 172

NP30A or NP40A

Table of Contents

Index

Maintenance and Lubrication

123

2019-03-11

Table of Contents

Index

407-502M

Row Delivery Tubing

It might be necessary to replace this tubing before the

10 year life if the knife or tine end of the tubing is

damaged by harsh field conditions.
When replacing delivery tubing:

• Use the same length of tubing as removed. This

length is identical for all rows of a specific applicator

model. This is required to ensure equal rate at each

knife or tine from the flow divider.

• Coil excess length. Secure it to the rear tool bar at

the row. For wing rows, coil inboard of the row, so

that the coil is below the knife or tine when the

applicator is folded.

Row Vapor Tubing

This is a different (larger ID) tubing compared to the row

delivery and refrigerant tubing.
It might be necessary to replace this tubing before the

10 year life if the knife or tine end of the tubing is

damaged by harsh field conditions.

Part ID

Service Life

Date Life Started

Replace Before Date

Great Plains

990-259R

10 Year rated life

Part ID

Service Life

Date Life Started

Replace Before Date

Great Plains

990-261R

10 Year rated life

A45

A48

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands