GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 104

Page: 104 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Adjustments

100

Knife Adjustment

Refer to Figure 79

Knives have no adjustments. Application depth is set by

the tool bar (page 96).
Knives have (Grade 5) shear bolts . Should the knife

encounter a substantial obstruction, such as a large rock,

or if speed plus conditions are too challenging, the shear

bolt fails, and the knife swings back on the (Grade 8)

mounting bolt .
A shear usually results in the need to replace all of:

802-038C

HHCS 1/2-13X2 1/4 GR5

803-020C

NUT HEX 1/2-13 PLT

804-015C

WASHER LOCK SPRING 1/2 PLT

804-094C

WASHER FLAT 1/2 HARD ASTMF436

Inspect tubing connections to the knife whenever

replacing a shear bolt.

Ammonia Exposure Hazard:

Discharge the system (page 115) before replacing a shear bolt.
Bolt replacement requires raising the applicator. Minimize

your vapor exposure. If shears are frequent, application may

be too deep, or the soil conditions too rough. Even with
cautious system discharges, your accumulated ammonia

exposure could exceed PEL and lead to health problems or

injury.

Ammonia Exposure

Hazard:

Do not back up with knives in ground to realign a knife for bolt

replacement. This will plug outlets on other knives.

-13 Grade 5 bolts are not immediately available,

temporarily substitute metric M12x1 Class 8.8.

Spring Shanks

Refer to Figure 80
If applicator is equipped with spring shanks (optional

item) the spring should be compressed to measure:

inch to 11

inch (28.6 to 28.9 cm)

once mounted. The distance is measured from end of

spring to end of spring.
Note: When encountering substantial obstructions in the

field, spring shanks help alleviate stress on the

knife shear bolt. Spring shanks reduce, but do not

eliminate all shear bolt failures.

Equipment Damage Risk:

Do not use a bolt strength higher than Grade 5, or

obstructions can result in machine damage. Using less than
Grade 5 results in nuisance shears.

Figure 79

Knife Shear Bolt

31593

Figure 80

Spring Shank

36006

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands