GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 140

Page: 140 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

136

Appendix A - Reference Information

Specifications and Capacities

NP30A Models, U.S. Customary Units

NP30A

-11C30

-12C30

-13C30

-25C15

Model

-11R30

-12R30

-13R30

-18R20

-11S30

-12S30

-13S30

-18S20

Row Count

Row Spacing

30 in.

20 in.

15 in.

Swath

27 ft. 6 in.

30 ft. 0 in.

32 ft. 6 in.

30 ft. 0 in.

31 ft. 3 in.

Working Width (Maximum)

26 ft. 11 in.

28 ft. 11 in.

31 ft. 7 in.

Transport Width

17 ft. 0 in.

Length (2 Point)

9 ft. 4 in.

Length (3 Point)

8 ft. 10 in.

n/a

Length (Pull Type)

17 ft. 4 in.

Wing Flex

8°

Working Height

6 ft. 10 in.

Transport Height (Folded)

12 ft. 6 in.

2P/PT Transport Clearance

16 in.

3P Transport Clearance

(depends on tractor 3-point hitch range)

n/a

140 hp

155 hp

165 hp

225 hp

300 hp

1 or 2 Circuits, 2250 psi, 4 gal/min

7700 lbs

7900 lbs

8100 lbs

9600 lbs

11900 lbs

7200 lbs

7400 lbs

7600 lbs

8800 lbs

n/a

11100 lbs

11300 lbs

11500 lbs

12800 lbs

15300 lbs

2P/PT Transport Tire Size

265/70B16.5 (10-16.5) NHS 8-Ply

PT Gauge Wheel Tire

265/70B16.5 (10-16.5) NHS 8-Ply

2P/3P Gauge Wheel Tire

20.5×8.0 10-Ply LR-E

3 to 7 inches

Rear Hitch

Option: Schuck Model 850

Nurse Tank Capability

3000 Gallons

Metering System

Raven Accuflow™ with CDS-JohnBlue Impellicone (Optional)

Controller Console*

Raven SCS 450 (Optional)

1. Power requirements vary significantly with conditions and practices.

3. Release depth is 3/4 in. above knife/tine depth, or 3/8 in. above coulter depth.
* Implement functions not monitored include: pressure and temperature

Min. Tractor HP Req.¹

Hydraulic Circuits Req.

Weight, 2P (maximum)²

Weight, 3P (maximum)²

Weight, PT (maximum)²

10-16.5 NHS

10-Ply

12-16.5 NHS

14-Ply

10-16.5 NHS

10-Ply

12-16.5 NHS

14-Ply

Operating Depth³

2. With Great Plains-installed AccuFlow metering, Schuck hitch, coulters and spider sealers. All weights are approximate.

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Brands by name

Popular brands