GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 83

Page: 83 / 172

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

2019-03-11

Table of Contents

Index

407-502M

11. Opening this bleed valve WILL release the

substantial amount of liquid NH

presently trapped in

the hose,

most likely as a spray

. Open the valve very

slowly, just until some fluid appears. Leave the valve

just slightly open.

12. Walk away, up-wind. Stay away until the release

concludes. Carefully open bleed valve completely to

confirm hose is discharged. For dual-cooler, repeat

step 9 through step 12 for the other hose.

13. Close all breakaway bleed valves (

x and

and any nurse tank hose valves

. Disconnect the

nurse tank half of the breakaway coupler at the

Acme coupler

14. Correct the cause of breakaway, only if trivial to do in

the field.

15. Consult the breakaway manual for re-coupling

instructions.

Before Re-connection: Elevated Exposure Hazard:

Exercise extreme care. Even if the nurse tank is undamaged,

sound and upright, a breakaway event is not a normal re-hitch

situation. A substantial NH

bleed is required that

WILL

release a flow of liquid anhydrous ammonia under pressure

If the wind is calm or light, do not attempt to bleed the nurse

tank hose(s).

Your field PPE

is not sufficient.

a. PPE: Personal Protective Equipment

A13

A16

A60

A57

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands