manualshive.com logo in svg

GRASS VALLEY KMV-3901, Installation & Service Manual, Page: 83 / 138

Share
Download
GRASS VALLEY KMV-3901 Installation & Service Manual Download Page 83

83

KMV-3901/KMV-3911

Installation & Service  Manual

Card LED, Overall alarm and GSM contribution

The 

Card LED

, 

Overall alarm

 and 

GSM contribution

 columns contain lists that allow you to 

set the level of contribution of each individual alarm to the alarm named in the column 
heading.

Card LED

This column allows you to configure the behavior of the KMV-3901/3911’s card-
edge status LED.

Overall alarm

This column allows you to configure the contribution of each individual alarm 
to the 

overall alarm

 associated with this card. Indicators for the overall alarm 

appear in the upper left corner of the control panel windows, and at the 
bottom of the 

Status/Name

 column.

GSM 
contribution

This column allows you to configure the contribution of each individual alarm 
to the GSM alarm status associated with this card. The GSM is a dynamic 
register of all iControl system alarms, and is also an alarm provider for external 
applications. The possible values for the GSM contribution are related to the 
overall alarm contribution:
• If the overall alarm contribution is set to 

Disabled

, then the GSM alarm 

contribution can be set to any available value.

• If the overall alarm contribution is set to any level other than disabled, then 

the GSM contribution follows the overall alarm.

Alternatively, select the 

Overall alarm and GSM contribution follow card LED

 

check box, to have the same contribution in all three contexts for the 
corresponding individual alarm.

Note:

N/A

 means the alarm is not user-configurable.

Overall 

alarm 

indicators

Summary of Contents for KMV-3901











































































































































Reviews:

No comments