Graco RoadLazer 231378 Instructions-Parts List Manual Download Page 20

Page: 20 / 54

308611

Service

Discard all locknuts upon removal, and replace with new ones.

Hydraulic Supply System Oil Change

CAUTION

Dust or dirt in the hydraulic system can damage the

hydraulic system components. Do not allow dust or

dirt to get into the hydraulic system when you service

the system.

Change the hydraulic oil as follows:

Relieve the pressure.

See page 16.

2. Place 15-gallon waste pail under hydraulic

reservoir drain plug.

3. Remove O-ring (438) and drain plug (439), and

drain reservoir.

4. Replace O-ring (438) and drain plug (439).

5. Remove nuts (405), gasket (425), and reservoir

cover (426).

6. Remove return line filter (436). Install new return

line filter.

7. Inspect inlet filter. Replace if necessary.

8. Install nuts (405), gasket (425), and reservoir

cover (426).

9. Fill reservoir with 12 gallons (45.4 liters) of Graco

Hydraulic Oil. Install fill cap.

10. Run RoadLazer, and cycle pumps for a few

seconds to fill hydraulic motors with hydraulic oil.

Recheck hydraulic oil level. Do not overfill.

Trailer Tire Removal

Fig.14.

WARNING

FALLING OBJECT HAZARD

A free-standing RoadLazer could

become unstable when raised by a

portable jack.

To reduce the risk of injury and equipment damage

Connect RoadLazer to tow vehicle before

raising with jack.

Follow instructions in this manual.

FAILURE TO FOLLOW THIS WARNING CAN

RESULT IN DEATH OR SERIOUS INJURY

1. Connect RoadLazer to tow vehicle.

2. Raise rear of RoadLazer with hydraulic jack.

3. Place blocks under RoadLazer as precaution

against jack failure or slippage.

4. Remove cotter key (528) from axle castle nut

(527).

5. Remove axle castle nut, axle bolt (531), and

spacers (530).

6. Remove lug nuts (A) and wheel.

NOTE:

Any service station can repair a RoadLazer

flat tire.

Fig. 14

530

531

527

528

530

06254A

Summary of Contents for RoadLazer 231378























































Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands

Graco RoadLazer 231378, Instructions-Parts List Manual

Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands