Graco RoadLazer 231378 Instructions-Parts List Manual Download Page 48

Page: 48 / 54

308611

Parts

RoadLazer Line Striper
Battery System

TI0265A

167

10(Ref)

9(Ref)

Ref.
No.

Part No.

Description

Qty.

Ref.
No.

Part No.

Description

Qty.

115753

BATTERY, 12V

107072

CABLE, electric, negative

107073

CABLE, electric, positive

801958

PROTECTOR, terminal, red

801959

PROTECTOR, terminal, black

803525

BOLT, battery

107069

CLAMP, battery

100527

WASHER, wrought

100016

WASHER, lock

102040

NUT, lock, hex, grade 5, 1/4--20
unc--3b

REF

102638

CAPSCREW, hex hd, grade 5,
3/8--16 unc--2a, 2 in. (51 mm) long REF

101566

LOCKNUT, nylon, 3/8--16

REF

100132

WASHER, flat

REF

100022

CAPSCREW, hex hd, grade 5,

3/8--16 unc--2a, 2 in. (51 mm) long

801972

PAD, battery

167

100015

NUT, hex, mscr, grade 5, 1/4--20
unc--2b

REF

Summary of Contents for RoadLazer 231378























































Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands

Graco RoadLazer 231378, Instructions-Parts List Manual

Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands