Graco RoadLazer 231378 Instructions-Parts List Manual Download Page 26

Page: 26 / 54

308611

Service

Paint Filter Replacement

Disassembly

1. Do

Flushing the System

procedure on page 14.

Relieve the pressure.

See page 16.

3. Set POWER ON/OFF on Programmable Skipline

Controller to OFF.

4. Set engine ignition key to OFF.

5. Remove paint outlet hose from ball valve (121).

6. Unscrew filter bowl (604) from filter housing (606).

7. Remove screen (602) from filter bowl (604).

8. Remove filter support (603) from filter bowl (604).

9. Remove spring (605) from filter bowl (604).

10. Remove O-ring (601).

Fig. 18

121

604

606

603

605

602

601

06257

(104361)

(167024)

(171941)

(193331)

(186075)

(185632)

Assembly

1. Install new O-ring (601).

2. Install spring (605) into filter bowl (604).

3. Install filter support (603) and screen (602) into

filter bowl (604).

NOTE:

Order 167025 if screen (602) is damaged.

Order 104361 for new O-ring.

4. Screw filter bowl (604) into filter housing (606).

Displacement Pump Service

See manual 308650.

Viscount I Hydraulic Motor Service

See manual 312484.

Bead Spray Gun Service

See manual 308612.

Paint Spray Gun Service

See manual 308613.

Stencil Spray Gun Service

See manual 311254.

Air Compressor

If the air compressor needs service, replace it.

Hydraulic Power Supply

If the hydraulic power supply needs service, replace it.

Summary of Contents for RoadLazer 231378























































Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands

Graco RoadLazer 231378, Instructions-Parts List Manual

Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands