Graco RoadLazer 231378 Instructions-Parts List Manual Download Page 17

Page: 17 / 54

308611

Application Data

Paint and Bead Guns

PAINT LINE WIDTH PER GUN

MPH (KPH)

4 in. (10 cm)

6 in. (15 cm)

8 in. (20 cm) 10 in. (25 cm) 12 in. (30 cm)

Paint Tip

221433

221439

GHD539

GHD839

GHD843

PSI (bar)

2000 (137)

3--4 (5--7)

Bead Nozzle

0.234

PSI (bar)

20 (1.4)

30 (2.1)

40 (2.8)

50 (3.4)

60 (4.1)

Paint Tip

221439

221443

221543

PSI (bar)

2000 (137)

5--6 (8--10)

Bead Nozzle

0.234

PSI (bar)

30 (2.1)

40 (2.8)

50 (3.4)

Paint Tip

221443

GHD445

PSI (bar)

2000 (137)

7--8 (11--13)

Bead Nozzle

0.234

PSI (bar)

40 (2.8)

50 (3.4)

Paint Tip

GHD445

PSI (bar)

2000 (137)

9--10 (14--16)

Bead Nozzle

0.234

PSI (bar)

50 (3.4)

These settings produce approximately a 15-mil

wet line with 6 lb of glass beads per gallon paint.

Different materials can produce different results.

See Bead Gun manual for additional application

rate information.

For GHDXXX paint tips use 222674 tip holder.
For 221XXX paint tips use 237859 tip holder.

Filter Information

Filters of 30 mesh are recommended for most

applications. For smaller tips or if frequent tip plugging

occurs, use 60-mesh filters.

Always use a 30-mesh stainless steel paint screen

167024 in the high-pressure filter bowls.

Spray Tip Information

Recommended spray tip for stencil hand gun painting

is 221425.

To spray 36 in. (91 cm) wide lines, install third gun kit,

and use three GHD839 or three GHD843 spray tips.

Summary of Contents for RoadLazer 231378























































Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands

Graco RoadLazer 231378, Instructions-Parts List Manual

Search results

Summary of Contents for RoadLazer 231378

Reviews:

Related manuals for RoadLazer 231378

Brands by name

Popular brands