Grace Company Q-Zone Queen Page 11 Assembly Instructions Manual Download

Page: 11 / 84

Frame Manual: Part Two

• Install the channel lock on the machine or

top plate.

• Prepare the top plate and home sewing

machine.

• Place the machine or top plate on the frame.

Quilting Machine Manual: Part Three

• Install the wheel covers, display, handles,

thread mast.

• Install the upper encoder.

Frame Manual: Part Three

• Install the rails and fabric bungees.
•

Position and adjust the rails.

•

Adjust the carriage stop.

•

Level the frame.

QuiltMotion Manual: Part Three

• Install the tablet bracket.
•

Plug in QuiltMotion.

• Use the quilting modes and settings in the

display.

• Maintain the machine and perform repairs.

Quilting Machine Manual: Part Four

Frame Manual: Part Four

•  Install the velcro tape
•  Install the cloth leaders
•  Attach the fabric

Summary of Contents for Q-Zone Queen





















































































Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands

Grace Company Q-Zone Queen, Assembly Instructions Manual

Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands