Grace Company Q-Zone Queen Page 76 Assembly Instructions Manual Download

Page: 76 / 84

Task 10 - Attaching the Fabric (continued)

Use a tape measure to measure seven inches from the right side of each of the rails. Mark these

positions with pieces of

tape

on each rail. You can use these marks to align your fabric and

make sure it is straight. These marks can be adjusted as needed depending on the size of your

quilts

Tape (x2)

Use a marker to draw a

dashed line

on the right side of your backing (the side you want to be

visible when the quilt is finished) about half an inch from the top edge.

To attach the

backing fabric

, place the fabric over the

quilt-backing rail

with the right side

facing down. Bring the top of the fabric under and behind the

take-up rail

so that the fabric is

above the top of the take-up rail and the dashed line from the previous step is on top.

Backing Fabric

Quilt-backing

Rail

Dashed Line

Part Four

Note

: Do not cover

the Fabri-Fast grooves

with the tape.

Summary of Contents for Q-Zone Queen





















































































Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands

Grace Company Q-Zone Queen, Assembly Instructions Manual

Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands