Grace Company Q-Zone Queen Page 50 Assembly Instructions Manual Download

Page: 50 / 84

Task 2 - Install the Cross Support Tubes (continued)

1. Place the end of a

cross support tube

so that it rests on the

shelf

of the corner

bracket on the front of the left leg. Loosely

attach it with two M6 x 10 connector bolts

and the 4 mm Allen wrench.

Cross Support Tube

Shelf

Connector Bolt

M6 x 10 mm (x2)

Crib Assembly Part One

1. Take the left leg and use the 4 mm Allen

wrench and two

M6 x 10 mm connector

bolts

to loosely attach a

corner brace

side B

to the front of the leg.

1. Use the 4 mm Allen wrench and loosely

attach a

corner brace side B

to the

back of the right leg with four

M6 x 10

connector bolts

Loosely screw in two more

M6 x 10 mm

connector bolts

in the brace holes on the

side of the leg.

Connector Bolt

M6 x 10 mm (x4)

Corner Brace B

Connector Bolt

M6 x 10 mm (x2)

Corner Brace B

Connector Bolt

M6 x 10 mm (x2)

Loosely attach a second

M6 x 10

connector bolt

to the side of the corner

brace.

Connector Bolt

M6 x 10 mm

Summary of Contents for Q-Zone Queen





















































































Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands

Grace Company Q-Zone Queen, Assembly Instructions Manual

Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands