Grace Company Q-Zone Queen Page 75 Assembly Instructions Manual Download

Page: 75 / 84

Task 10 - Attaching the Fabric

Parts & Tools Needed:

Instructions

Take the following steps to prepare and attach your fabric to your frame:

Scissors

(not included)

Pins

(not included)

Measure and cut the pieces that you will use for your “quilt sandwich.”

Cut the batting to be about 8-10 inches wider and longer than your quilt top.

Cut the backing to be about 4-6 inches wider and 27 inches longer than your batting.

Note:

The Grace Company strongly

recommends using cloth leaders to help

attach your fabric because they allow you

to use less backing fabric, which saves

you money, and they also make attaching

the fabric easier. Visit graceframe.com for

pricing and other information.

27”

Backing

Batting

Quilt Top

4-6”

8-10”

Fabri-Fast Tool

Marker

(not included)

Tape Measure

(not included)

C-Clamp (x4)

Fabri-Fast

Tubing (x2)

Bungee Clamp

Accessory (x4)

Part Four

Summary of Contents for Q-Zone Queen





















































































Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands

Grace Company Q-Zone Queen, Assembly Instructions Manual

Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands