Grace Company Q-Zone Queen Page 57 Assembly Instructions Manual Download

Page: 57 / 84

Congratulations! You have completed Part One of the Crib Assembly

instructions for the Q-Zone Queen Frame.

If you are also installing a new Q’nique quilting machine, turn to Part

One of your machine manual now.

If you are going to be using a top plate with a domestic sewing

machine, turn to your top plate manual and follow the instructions to

fully assemble the top plate.

If you are not installing a new machine or top plate, but are installing

QuiltMotion, turn to Part One of your QuiltMotion manual before

moving on to Part Two of this manual.

If you are not installing a Q’nique machine or QuiltMotion at this time,

continue to Queen Assembly Part Two of this manual on page 58.

Crib Assembly Part One

Summary of Contents for Q-Zone Queen





















































































Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands

Grace Company Q-Zone Queen, Assembly Instructions Manual

Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands