Grace Company Q-Zone Queen Page 19 Assembly Instructions Manual Download

Page: 19 / 84

1. Take the left leg and use the 4 mm Allen

wrench and two

M6 x 10 mm connector

bolts

to loosely attach a

corner brace

side B

to the front of the leg.

1. Use the 4 mm Allen wrench and loosely

attach a

corner brace side B

to the

back of the right leg with four

M6 x 10

connector bolts

Loosely screw in two more

M6 x 10 mm

connector bolts

in the brace holes on the

side of the leg.

1. Use the 4 mm Allen wrench and loosely

attach a

corner brace side A

to the

back of the left leg with four

M6 x 10

connector bolts

Connector Bolt

M6 x 10 mm (x4)

Corner Brace B

Connector Bolt

M6 x 10 mm (x2)

Corner Brace B

Connector Bolt

M6 x 10 mm (x2)

Corner Brace A

Connector Bolt

M6 x 10 mm (x4)

Middle Leg Brace (x2)

Connector Bolt

M6 x 10 mm (x4)

Task 2 - Install the Cross Support Tubes (continued)

Queen Assembly Part One

Loosely attach the two

middle leg braces

to the middle leg using four

M6 x 10 mm

connector bolts

and the 4 mm Allen

wrench.

Loosely attach a second

M6 x 10

connector bolt

to the side of the corner

brace.

Connector Bolt

M6 x 10 mm

Summary of Contents for Q-Zone Queen





















































































Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands

Grace Company Q-Zone Queen, Assembly Instructions Manual

Search results

Summary of Contents for Q-Zone Queen

Reviews:

Related manuals for Q-Zone Queen

Brands by name

Popular brands