manualshive.com logo in svg

Gorilla Playsets 1500IWF, Manual

Share
Download
Gorilla Playsets 1500IWF Manual Download Page 82

STEP 23: REAR CORNER POSTS & DECK SUPPORTS & 

SIDE TOP PANEL BOARDS

4: ATTACH THE BOTTOM OF THE REAR CORNER POSTS TO THE SIDE SANDBOX BOARDS WITH 5/16" X 4-1/2" HEX 

BOLTS AND 5/16" WASHERS.
5: TIGHTEN ALL THE FASTENERS.

3: PLACE THE 2 X 4 X 34" UPPER LEVEL DECK SUPPORTS ON THE INSIDE OF THE LAG/CORNER POSTS.  ATTACH EACH 

UPPER LEVEL DECK SUPPORT WITH 5/16" X 4-1/2" HEX BOLTS AND 5/16" WASHERS.

1: HAMMER A T-NUT INTO THE HOLES AT THE TOP OF THE LAG POSTS.
TIP: BEFORE YOU INSTALL THESE BOARDS LEAVE THEM ALL A LITTLE LOOSE.  WHEN YOU HAVE FASTENERS IN ALL THE 

BOARDS GO BACK AND TIGHTEN THEM ALL UP.
2: PLACE THE 2 X 4 X 30-7/16" SIDE TOP PANEL BOARDS (OFFSET DOWN) AT THE TOP OF THE CORNER POSTS ON 

THE SIDES OF THE FORT.  USE 5/16" X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH EACH SIDE TOP PANEL 

BOARD TO THE LAG/CORNER POSTS.

HEX BOLT

5/16" X 4-1/2" 

(LEFT SIDE)

CORNER POST

(RIGHT SIDE)

4 X 4 X 120

5/16" X 4-1/2" 

HEX BOLT

 

CORNER POST

5/16" WASHER

5/16" WASHER

T-NUTS

T-NUTS

2 X 4 X 30-7/16"
(OFFSET DOWN) 

SIDE TOP PANEL BOARD

4 X 4 X 120

2 X 4 X 34"

UPPER LEVEL 

DECK SUPPORT

2 X 4 X 30-7/16"

SIDE TOP PANEL BOARD

(OFFSET DOWN) 

5/16" 

WASHER

5/16" X 4-1/2" 

HEX BOLT

72

Summary of Contents for 1500IWF














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands