manualshive.com logo in svg

Gorilla Playsets 1500IWF, Manual

Share
Download
Gorilla Playsets 1500IWF Manual Download Page 154

BOTTOM BRIDGE RAIL

TOP BRIDGE RAIL

AND 5/16" WASHERS

POSTS ON EACH SIDE WITH

5/16" X 3-1/2" LAG SCREWS

REMOVED FROM VIEW

FOR CLARITY.

ATTACH TOP AND LOWER

BRIDGE RAILS TO CORNER

NOTE: SOME BOARDS

ATTACH

5/4 X 3 X 28-1/4"

PANEL SLAT 

WITH 2" WOOD SCREWS

 16" 

 59" 

1: PLACE THE BRIDGE RAILS AGAINST THE GREEN CORNER POST AND CENTER CORNER POST ON 

THE PLAY SET.
2: LEVEL EACH TOP BRIDGE RAIL AND ATTACH THEM TO THE CORNER POSTS WITH 5/16" X 3-1/2" 

LAG SCREWS AND 5/16" WASHERS.
3: MAKE THE BOTTOM OF EACH LOWER BRIDGE RAIL 16" FROM THE TOP OF THE TOP BRIDGE RAIL.
4: ATTACH EACH LOWER BRIDGE RAIL TO THE CORNER POSTS WITH 5/16" X 3-1/2" LAG SCREWS 

AND 5/16" WASHERS.
5: ATTACH 5/4 X 3 X 28-1/4" PANEL SLAT TO ROPE LADDER SUPPORT AND FRONT FACE BOARD, 

NEXT TO THE BRIDGE RAIL WITH 2" WOOD SCREWS.

STEP 14: BRIDGE RAILS TO PLAY SET

144

Summary of Contents for 1500IWF














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands