manualshive.com logo in svg

Gorilla Playsets 1500IWF, Manual

Share
Download
Gorilla Playsets 1500IWF Manual Download Page 66

STEP 7: REAR FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD ON THE BOTTOM REAR OF THE CORNER POSTS. THE HOLES IN THE

SANDBOX BOARD MUST BE OFFSET UP.
2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO 

THE T-NUTS INSTALLED IN THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.
3: PLACE THE 2 X 6 X 70" BACK PANEL BOARD AT THE MIDDLE OF THE REAR CORNER POSTS. THE HOLES IN

THE BACK PANEL BOARD MUST BE OFFSET DOWN.
4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE BACK PANEL BOARD

TO THE T-NUTS INSTALLED IN THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

(OFFSET DOWN)

BACK PANEL BOARD

(OFFSET UP)

WASHER

5/16"

2 X 6 X 70"

SANDBOX BOARD

2 X 6 X 70"

5/16" X 4-1/2"

HEX BOLT

56

Summary of Contents for 1500IWF














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands